xTool O1 Omni jig for golf ball blanks
With 0.3 mm clearance per side, 4 mm webs and a 10 mm margin, the xTool O1 Omni (UV printer)'s 330 × 420 mm work area fits 54 pockets for golf ball blanks, in 9 staggered rows. A straight grid would hold 48; offsetting every other row by half a pocket gains 6.
- Blanks per run
- 54
- Layout
- 9 staggered rows
- Blank
- 42.67 × 42.67 × 42.67 mm (≥ 1.680 in Ø)
- 30 × 30 mm
- Clearance
- 0.3 mm per side
- Jig
- Laser-cut 6 mm sheet, through-holes
- Plate
- 330 × 420 mm, 10 mm margin, 4 mm webs
- Tallest point
- 42.7 mm
- Cut path
- 6.58 m
Cut file in millimetres: red = cut, blue = engraved labels and marks. Adjust anything below and download the 3MF, STL, DXF and alignment template.
What to know before you cut
The 0.3 mm starting clearance assumes a 3D-printed jig without hole compensation. Cut the test-fit coupon (0.0 to 0.5 mm) in the generator before the full plate: blanks from different suppliers vary, and the laser's kerf makes cut holes slightly larger than drawn.
Golf balls sit in 30 mm seat holes in a 6 mm plate, so the top of each ball stands about 42.7 mm above the bed. The printable cap on a ball is small, so keep logos near the top.
This staggered layout cannot be split into 256 mm tiles without cutting through pockets; switch to a grid in the generator, trim the plate, or print it on a larger printer.
The Rules of Equipment set a minimum diameter of 1.680 in and no maximum. The jig cuts a 30 mm seat hole; the ball's footprint sets the spacing.
Adjust this jig
The generator below starts from this machine and blank. Change the clearance, layout or jig build, then download the files.
54 pockets, 9 staggered rows, on a 330 mm × 420 mm plate.
- Pockets
- 54
- Plate
- 330 mm × 420 mm
- Cut path
- 6.58 m
- Sheet used
- 1386 cm²
- Tallest point
- 42.7 mm
Cut it
Red = cut, blue = engrave. Millimetre units.
Print it
Through-holes in a plate. Millimetres.
Line up the artwork
Template with pocket centres, blank edge, bleed and safe area, placed where the jig sits on the machine.
Other xTool O1 Omni jigs
- Acrylic keychain, 2 in round: 40 per run
- Coaster, 4 in square: 6 per run
- AirPods 4 case: 42 per run
- Metal business card: 21 per run
- Phone grip top, round: 65 per run
Golf ball jigs for other machines
- eufyMake UV Printer E1: 54 per run
- Mimaki UJF-3042 MkII e: 50 per run
Guides
- UV printer jig: how to make one that holds every blank
- Alignment templates for UV printing
- Jig clearance: how much gap per side
Sources
- xTool O1 Omni baseplates (xTool support) (work area, checked 2026-10-17)
- R&A / USGA Rules of Equipment, Part 4: balls (blank size)
Machine and product names are used only to describe compatibility. Pocketplate is not affiliated with xTool.
Get blank packs and Pro first
Everything here is free during the beta. Ready-made packs for common blanks and a Pro tier are next. Tell us which one you would pay for.